Plumbing Basics: A Must for Bathtub Installation
Plumbing Basics: A Must for Bathtub Installation
Blog Article
Were you searching for answers on A Step-by-Step Guide to Installing a Bathtub?
Setting up a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old tub with a brand-new one is also a reasonably difficult task. If the old tub is readily accessible, the job can move immediately; if you have to open a wall to remove the old tub and place the brand-new tub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old tub as well as set in the new one. Make certain you have actually certified on your own for the job as well as are comfortable trying it. Instead of working with a service provider to take over a halfway-completed task, it is far better to think about employing one before you start. Possibilities are you may need a professional plumber to make tube links.
This short article will help you mount a brand-new tub in your washroom if you have actually currently gotten a new bathtub as well as do not require to alter the setup of your previous water pipelines.
Your devices and material list ought to make up the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the supply of water. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome due to the restricted accessibility that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel all set for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been eliminated, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washing machines are in location between the faucet and the sink. Secure the tap in position with the manufacturer given backnut. Once the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet ports. The previous kind needs to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the required position. The wood boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four small points.
The next objective is to make certain that the tub is leveled all round. This can be achieved by checking the spirit level as well as adjusting the feet on the bath tub till the level reviews level.
To install taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipeline by making a compression join; after that do the exact same for the various other tap.
Switch on the supply of water and also inspect all joints and also brand-new pipework for leakages and tighten them if needed. Fill up the bath tub as well as additionally examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will certainly resolve it right into its final setting.
Getting ready for the Installment
To start with, the supporting structure provided with the bathroom should be fitted (if called for) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a rigid seal, causing the water to permeate the wall in between the bath and also the tiling, causing problems with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and also can sealing voids up to a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked paper or soft rope. Remember to always fill the bathtub with water before securing, to permit the activity experienced when the bathtub remains in usage. The sealant can break fairly early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on How to Install a Bathtub? Leave feedback down the page. We will be interested to know your responses about this blog posting. We hope that you come back again in the future. Enjoyed our blog posting? Please share it. Help other people locate it. Thank you so much for taking the time to read it.
Request An Appointment Report this page